1979 Fender Twin (very slow) restoration
- laurie
- Posts: 1652
- Joined: Fri Aug 17, 2018 2:07 am
- Location: Canada
- SBZ: Multi Platinum
- Bossarea: Multi Platinum
Re: 1979 Fender Twin (very slow) restoration
The behemoth Twin is finished.
Who needs paint-stripper? Crank this thing to 10 and the paint will fall off the walls
Pics to follow.
Who needs paint-stripper? Crank this thing to 10 and the paint will fall off the walls
Pics to follow.
- Pepe
- Posts: 1688
- Joined: Thu Aug 16, 2018 2:19 pm
- Location: Germany
- SBZ: Multi Platinum
- Bossarea: Double Platinum
- Contact:
Re: 1979 Fender Twin (very slow) restoration
Congratulations for the repair! So sad that a tube failed.
- laurie
- Posts: 1652
- Joined: Fri Aug 17, 2018 2:07 am
- Location: Canada
- SBZ: Multi Platinum
- Bossarea: Multi Platinum
Re: 1979 Fender Twin (very slow) restoration
Now that it has been a couple of weeks since the initial rebuild I've had time to play the 135W twin a bit more and do a bunch more research.
This model twin does not have a bias adjustment on it - the bias is fixed, and the only adjustment is a "tube matching" potentiometer, which doesn't add any value when you buy a matched quad of tubes.
The tubes are running "cold" - a measured bias current of 20mA. This amp needs about 40mA bias current, so there is a lot of cross-over distortion. It is good sounding distortion, but the amp is not giving the traditional clean Fender tone - it is always a little "dirty".
When I get some time over the next few weeks I will rebuild the tube matching circuit into a proper "blackface" bias circuit. Just needs 3 resistors changed and rewiring the hum balance potentiometer.
I use a Eurotubes "Pro One" bias meter:
https://www.eurotubes.com/store/pc/bias%20probes.htm
I'm still not thinking I'll keep it (it weighs north of 80 pounds) and 135W is ridiculous, even if they are "Fender Watts".
This model twin does not have a bias adjustment on it - the bias is fixed, and the only adjustment is a "tube matching" potentiometer, which doesn't add any value when you buy a matched quad of tubes.
The tubes are running "cold" - a measured bias current of 20mA. This amp needs about 40mA bias current, so there is a lot of cross-over distortion. It is good sounding distortion, but the amp is not giving the traditional clean Fender tone - it is always a little "dirty".
When I get some time over the next few weeks I will rebuild the tube matching circuit into a proper "blackface" bias circuit. Just needs 3 resistors changed and rewiring the hum balance potentiometer.
I use a Eurotubes "Pro One" bias meter:
https://www.eurotubes.com/store/pc/bias%20probes.htm
I'm still not thinking I'll keep it (it weighs north of 80 pounds) and 135W is ridiculous, even if they are "Fender Watts".
- laurie
- Posts: 1652
- Joined: Fri Aug 17, 2018 2:07 am
- Location: Canada
- SBZ: Multi Platinum
- Bossarea: Multi Platinum
Re: 1979 Fender Twin (very slow) restoration
UPDATE:
The output tube sockets were having some issues. The connectors for some of the pins were losing tension and could not be fixed. Plus I did some more work on it. It is now completely finished. This is the full list of stuff done:
The output tube sockets were having some issues. The connectors for some of the pins were losing tension and could not be fixed. Plus I did some more work on it. It is now completely finished. This is the full list of stuff done:
- All new electrolytic capacitors (a “recap”).
- Brand new Apex matched quad of JJ 6L6GC output tubes installed.
- Old tired output tube sockets replaced with new ceramic sockets.
- Output tube control-grid and screen-grid resistors upgraded to resistance-matched 2W resistors.
- There is no bias control in the original circuit. The original “output tubes matching” circuit has been upgraded to a Blackface Twin (AB763) bias circuit. The amp can now actually be biased.
- All preamp tubes (12AX7, 7025, 12AT7) tested on a tube-tester and weak ones replaced.
- Vibrato opto “roach” replaced with a custom-made LED roach. The 0.01MFD vibrato grounding cap replaced. Vibrato is now dead silent (no ticking or thumping).
- The ground switch and associated capacitor removed (the so-called “death cap”).
- Damaged original power cord upgraded to a modern 12 foot long cord.
- Broken fuse-holder replaced.
- Dodgy power and stand-by switches replaced with Fender factory parts.
- All potentiometers and switches cleaned and lubricated. The contacts in all switched jacks cleaned, retensioned, and lubricated.
- New Fender factory footswitch and dust cover.
- Dirk
- Posts: 217
- Joined: Fri Aug 17, 2018 1:28 pm
- Location: Netherlands
- SBZ: Double Platinum
- Bossarea: Double Platinum
Re: 1979 Fender Twin (very slow) restoration
That looks great, Laurie
Re: 1979 Fender Twin (very slow) restoration
So cool! The amp thanks you for bringing it back to full health!